How to Know Whether an ABG Sample Is Correct?

“Is this ABG reliable?”

Before interpreting numbers, you must confirm the sample is valid.

ABG errors are usually pre-analytical (most common) rather than machine errors.

 Common ABG Errors in ICU

 Step 1 — Confirm It Is Truly ARTERIAL

 Arterial vs Venous Values

 Step 2 — Check Clinical Correlation

Ask:

• Does SpO₂ match PaO₂?
• Does patient’s respiratory status match PaCO₂?
• Does shock match lactate?

Example:

SpO₂ = 99%
ABG PaO₂ = 52 mmHg means  Something is wrong.

Possible causes:

• Air bubble
• Analyzer delay
• Sample mix-up

 Step 3 — Check for Air Bubble Contamination

Air contains:

• PO₂ ≈ 150 mmHg
• PCO₂ ≈ 0

If air contamination occurs:

Clue:
Unexplained respiratory alkalosis + high PaO₂.

 Step 4 — Check Time to Analysis

ABG must be analyzed within:

• 10–15 minutes (room temp)
• 30–60 minutes if iced

If delayed:

• Cells continue metabolism
• CO₂ ↑
• O₂ ↓
• pH ↓

Clue:Metabolic acidosis in stable patient without cause.

 Step 5 — Heparin Dilution Error

Excess liquid heparin can cause:

Always use:

• Dry balanced heparin syringes.

• 0.5 mL of liquid heparin (2–5 IU of heparin per mL of blood)into the syringe.
• How Much Blood Should Be Collected?—Minimum:1–1.5 mL ,Too small sample → heparin dilution effect more pronounced.

Why Heparin Causes Metabolic Acidosis on ABG

Heparin solution is slightly acidic.

Excess heparin:

• Dilutes bicarbonate
• Reduces measured HCO₃⁻
• Causes apparent metabolic acidosis

But patient is actually normal.

 Why 2 mL or 3 mL Size syringe ?

ABG machines require:

• ~0.5–1 mL minimum blood
• But ideally 1–1.5 mL for accurate analysis

So:

• 2–3 mL syringe gives adequate capacity
• Prevents over-dilution (if using liquid heparin)
• Easy handling for arterial puncture

Large 10 mL syringes ❌ are not ideal because:

• More dead space
• More air contamination risk
• More heparin dilution
• Less precise control

 What Is an “ABG-Type” Syringe?

It is different from a routine injection syringe.

It has:

✔ Gas-tight plunger
✔ Minimal dead space
✔ Thin needle (23–25G)
✔ Luer-lock cap
✔ Often pre-heparinized (dry balanced)
✔ Smooth self-filling design

 Step 6 — Check Internal Consistency (Henderson–Hasselbalch Rule)

If pH, HCO₃⁻, and PaCO₂ do not mathematically match:

❌ Analyzer error or transcription error.

 Using the H⁺ Ion Table?

There is a fixed mathematical relationship between pH and hydrogen ion concentration (H⁺).

Approximate relationship:

Rule of thumb:

For every 0.1 drop in pH → H⁺ increases by ~25%.

  Why Is This Useful?

Because acid–base disorders ultimately reflect changes in H⁺ concentration.

So if:

• pH and PaCO₂ suggest acidosis
• But HCO₃⁻ does not explain that H⁺ level

→ ABG may be inconsistent.

 How to Use H⁺ for Validity Check

H+≈24×PaCO2/HCO3

This comes from rearranged Henderson–Hasselbalch.

If calculated H⁺ does NOT match pH-derived H⁺ → suspect error.

 Example — Invalid ABG:

pH = 7.40 → H⁺ ≈ 40
PaCO₂ = 60
HCO₃⁻ = 24

Now calculate:

24 × 60 / 24 = 60

Calculated H⁺ = 60

But pH 7.40 corresponds to H⁺ = 40.

Mismatch ❌

This ABG is mathematically inconsistent.

 Step 7 — Check Oxygenation Logic (Alveolar Gas Equation)

If patient is on 50% FiO₂:

Expected PaO₂ ≈ 5 × FiO₂ (%)
≈ 250 mmHg

If PaO₂ is 60 mmHg:
Either:

• Severe shunt
  OR
• Sample error

Always calculate A–a gradient.